English-language podcasts

Ask the A&Ps

"Shock cooling is a myth"

52 min

Listen through the publisher, then discuss the episode here or arrange an in-person Roundtable. Your city determines where to meet.

Roundtables are designed for groups of four, with a shared subject and room for everyone to speak. Come for discussion, with no dating expectation.

Engines fail when they're new, not old. Plus, leaning with carb heat, questions to ask as a renter, and Cirrus cylinder cracking. Email [email protected] for a chance to get on the show. Join the world's largest aviation community at aopa.org/join Full notes below: Kevin is looking to rent an airplane from a private owner and he's looking for opportunities on Facebook. When he goes to see the airplane and meet the owner, Kevin is wondering what he should ask. Paul suggests staring with the logbooks and looking for the annual inspection sign off with a note that the ADs have been complied with. Colleen says to start with the books and then go through a thorough pre-flight. If the owner balks at repairs that you consider essential, she suggests walking. The hosts debate the importance of how many people fly the airplane, but settle on the fact that what really matters is a standard squawk sheet. Alan is concerned about the new Cirrus service bulletin that describes cylinder cracks on Continental engines. He asked the shop to inspect per the service bulletin and the shop found a crack where the SB describes. Paul said all you can do at this point is to inspect it frequently, ideally every time the cowling is off. The manifold pressure pull and other pilot actions won't impact this. It's a design defect that has nothing to do with pliot actions.Ike flies an O-200 and he thinks it runs better lean with full carb heat on while in cruise. He's wondering if the unfiltered air is bad for the engine. The hosts say so long as he's only doing it in cruise, it's no problem. Colleen does this with one of her airplanes and her oil analysis doesn't show any additional silica in her oil. Mike suggests he try partial carb heat to get the same effect.Lawrence and his son fly the family's new airplane. He wants to instruct, and his son wants to fly for a career. They've flown 400 hours or so, and the engine is around 2,000 hours since TBO. They do a lot of their own maintenance under supervision, and as Lawrence learns more he wants to be sure he is being safe. Specifically he's looking for signs of when to start worrying about TBO. The engine that you have is more reliable than what you're going to have after you overhaul, Paul said. Colleen mentioned new, defective parts on new engines. The team focus on maintenance-induced failures, etc. The most common reason the engine will need to be overhauled, Mike said, is if the cam and lifters are doing bad. This will show in metal in the filter. But these issues aren't safety issues so much as financial problems. It's about a bulletproof an engine as you can get, Mike says. Accidents caused by engine failure almost always occur when the engines are young, not old, according to Mike. Lawrence wants to focus on what really matters. Mike says there are three things--boroscoping, checking for metal in the oil filter and screen, and watching for symptoms of morning sickness.

Episode information is provided by the publisher. Listening takes place on the publisher’s service.

Listen at the source ↗

Featured places to meet in Palo Alto, CA

Explore these places and arrange a conversation through ThinkMatch.

City guide for Palo Alto, CA

More from Ask the A&Ps

Ask the A&Ps

"Can I make the engine blow less oil?"

66 min

Owner-produced parts, manuals, blow by and more. Send your questions to [email protected] for a chance to get on the show. Join the world's largest aviation community at aopa.org/join Full episode notes below: Daniel wonders whether it's possible to make your own parts. The hosts explain that the standard is that owner-produced parts must be at least as good as the original, meaning they can be even better. To achieve that standard they recommend going to a machine shop or good mechanic who can reverse engineer it. Paul said Textron is really good about sharing information, and sometimes even basic drawings, especially if they no longer produce the part. Key to this is that the mechanic must be ok with it, and supportive. Mike further points out that a minor alteration only needs acceptable data, while a major repair requires approved data. Given that this is a minor repair, Daniel can even use acceptable data or methods. Jerry is an IA who is wondering how to deal with manuals. This i

Discuss this episode

Community Poll

A majority vote should not override the basic rights of a smaller group.

Share your view, then see how readers voted. No sign-in required. This poll is shared across stories.

Do you agree or disagree?

Choose one answer

Common Quandary

A Common Quandary to discuss

Another conversation to explore, separate from this news story.

Your new television goes on sale elsewhere. Can you return it and buy the identical one cheaper?

A week after buying a television, another store offers the same model for much less. Your retailer refuses to match the price but allows unopened-looking returns. You could carefully repack the perfectly functional set.

Is a generous return policy permission to reverse a deal for any reason?

Explore this quandary